Smart brain board for hi-efficiency charging. 1 to 10 cells handling capability. This unit accepts 12VDC or 220-240VAC input. Works on almost any Ni-Cd & Ni-MH type battery, 50 to 4000mAh battery capacity, 0.1A to 5.0A charge rate. Smart trickle (0mA, 50mA, 100mA). Delta peak detection. Battery reverse protection. Built-in buzzer & cooling fan, internal 14A power supply. This unit is very versatile and accept three different kinds of power source; 12VDC, 100-120VAC or 200-240VAC. Dimensions: 234x223x80mm. Weight 1542g

16X4-PRO AC/DC Charger with LCD display, 1-15 cells capability, VESC F-1 Linear Charge, discharge, cycle, 50-9999mAh, up to 5.5A charge rate, 4A discharge rate, auto logout, auto deltaV works with both Ni-Cd & Ni-MH packs, display shows voltage, current and capacity in mAh, internal high speed fan keeps the unit cool, user replacable 10A fuse protected, this charger is very user friendly, operate at close to room temperature and can handle many different kinds of battery pack, you can charge 1 cell for glow plug, 12V pack for starter box, ideal for electric cars, nitro cars, Mini & Micro, TX & RX packs, heli & plane, boat and drag racing.

Full-featured charger, user-friendly, 6 modes for Ni-Cd and Ni-MH packs, built-in output protection, built-in battery conditioning, reverse input voltage protection, built-in fan, detachable AC and DC cords. This unit accepts 12VDC or 110-120VAC input. This charger is officially approved for charging nickel metal hydride battery packs, AC/DC 16-Bit digital charger, 4-7 cells, charges, discharges, cycles, built-in TX/RX slow charging, 6 modes of operation, 0.5-4.5A charge rate, 1A discharge rate, very small and light weight, VESC high voltage & fuzzy logic mode charging

This is a modified steering block, comes with four larger ball bearings (15mm) for Super-Duty performance, this part is machined to be as light possible, we suggest users to use either plastic pivot ball caps or special pivot ball caps with o-ring, use threadlock if the stock metal pivot ball caps are to be used with alloy steering blocks. Why buy RPM knuckles when these are stronger, have no flex for better steering control and just plain LOOK better!?

This is a modified steering block, comes with four larger ball bearings (15mm) for Super-Duty performance, this part is machined to be as light possible, we suggest users to use either plastic pivot ball caps or special pivot ball caps with o-ring, use threadlock if the stock metal pivot ball caps are to be used with alloy steering blocks. Why buy RPM knuckles when these are stronger, have no flex for better steering control and just plain LOOK better!? These are the same as the ones mentioned above, but blue in color.

Alloy Gear Box for E/T-Maxx This is a must have item if you plan on running serious power through your truck. Eliminate stripped ring gears by using this lightweight, strong diff case. The gears mesh perfectly and the diff case flex is gone!

Alloy Front Lower Arm (L+R) for Revo.

Alloy Front Upper Arm (L+R) for Revo

Alloy Rear Lower Arm (L+R) for Revo

Alloy Rear Upper Arm (L+R) for Revo

Aluminum Alloy Lower Suspension Arm fits Tamiya TNX and Terra Crusher, front or rear. These lightweight aluminum parts add strength and style to your truck!

Aluminum Alloy Upper Suspension Arm fits Tamiya TNX and Terra Crusher, front or rear. These lightweight aluminum parts add strength and style to your truck!

Upgrade to the strength and style of polished aluminum. This steering block is lightweight, super strong and looks good, too!

Also works for Terra Crusher! Upgrade to the strength and style of polished aluminum. This castor block is lightweight, super strong and looks good, too!