RC-Monster Forums

RC-Monster Forums (https://www.rc-monster.com/forum/index.php)
-   General Discussion (https://www.rc-monster.com/forum/forumdisplay.php?f=20)
-   -   Pay It Forward! (https://www.rc-monster.com/forum/showthread.php?t=21566)

Arct1k 06.13.2009 10:00 AM

Pay It Forward!
 
This is an honor based system but these are the ground rules...

- No asking for stuff
- You have to post up something if you take something
- Taker pays shipping unless offered by giver
- Take only what you need
- No reselling - If item is no longer required re-PIF
- Smile :yipi:

BL_RV0 06.13.2009 01:00 PM

All I have to PIF is a set of electric rustler front wheels/tires.

nitrostarter 06.13.2009 02:19 PM

I have a HItec Aggressor 2ch AM transmitter and Futaba AM rx.

skellyo 06.13.2009 07:25 PM

Ok, here's some more goodies that need to go:

6 Foam inserts, I believe 4 are from Losi Rock Claws and I have no idea where the other 2 are from, but they are from 2.2's

http://skellyo.com/fs/pif_foams.jpg



CVD's for an Associated T3

http://skellyo.com/fs/pif_t3cvd.jpg


Gear Cover for Traxxas Stampede/Slash/Bandit/Rustler

http://skellyo.com/fs/pif_trxcover.jpg


Turnbuckles for Traxxas VXL Rustler (I believe)

http://skellyo.com/fs/pif_turnbuckles.jpg

Gee 06.14.2009 03:34 AM

Got some GP3300 7cell Nihms if any could use them. They look like crap but I really wasn't into making packs that looked good. Just needed to fit. They haven't been used in a long time in a rc. I have cycled them on the charger every month or month and half. The last reading after they cycles seemed promissing. I've found they tend to not last long for a few runs but start getting thier legs back after they are used and charged a couple times. They were still great pack when I put them on the shelf after going lipo.

http://i212.photobucket.com/albums/c.../7cellp123.jpg

You can see the voltage readings of them in this link. If it would help any I can take a picture that would show them from a much greater distance.

http://s212.photobucket.com/albums/c...ade/?start=all

Heres some RPM shock towers, front, rear, and center skid plates for the 3906 e-maxx. The shock towers were dyed Black Plum. There also is a small center skid plate made from CF that protects the tranny.

http://i212.photobucket.com/albums/c...andtowers1.jpg


Some small losi 2.2 tires (only 2 of them)

http://i212.photobucket.com/albums/c...si22pins1a.jpg

and a VXL differential that is filled with jb weld for that spool effect.

http://i212.photobucket.com/albums/c...lockeddiff.jpg

nitrostarter 06.14.2009 02:18 PM

also have 4 GP3300 6 cell packs. Not sure on the condition.

brushlessboy16 06.14.2009 09:51 PM

I have Lots of Duratrax evader parts- trans is toasted... Needs too shocks.. no wheels and tires

trev3813 06.15.2009 12:02 PM

I have a set or rustler wheels and tires off a xl5.

bigboi146 06.17.2009 12:30 AM

I have these. (40 series only)

Gee 06.28.2009 07:02 PM

Memory sticks - came out of a Dell Optiplex GX620 X86-based PC

Samsung
(2) 256MB 1Rx16 PC2-4200U-444-12-C3
(1) 256MB 1Rx16 PC2-4200U-444-12-C1
(1) 512MB 1Rx8 PC2-4200U-444-12-D3

riverat1540 07.16.2009 12:08 AM

i have 2 sets of 20mm hub adapters for a savage, i have no need for them, 20mm is the 420 sized rim from losi, like on the muggy

also still have 3 /genesis/nemesis/gst tires just need busted up rims removed.

riverat1540 07.19.2009 12:00 AM

i have an old astro flight ac/dc charger charges up to to 8 cells and up to 7amps,
pm for pics and details

Arct1k 08.01.2009 11:27 PM

I've some used badlands - Gone

stock old emaxx tires - available

Hyper 7 - lower F arms

eovnu87435ds 08.03.2009 04:56 PM

I have lots of spare parts for a hyper 7, or similar fitting buggy. an Rx pack or 2.

PM with what you need

Modding_out 08.19.2009 10:58 AM

I have a bunch of radio shack 3300 cells if any one wants them....not in the best condition, but they hold a charge


All times are GMT -4. The time now is 05:44 AM.

Powered by vBulletin® Version 3.8.1
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.