RC-Monster Forums  
RC Monster

Go Back   RC-Monster Forums > Search Forums

Showing results 1 to 19 of 19
Search took 0.00 seconds.
Search: Posts Made By: prhess
Forum: Novak 12.20.2009, 11:36 PM
Replies: 2
Views: 5,166
Posted By prhess
With a larger diameter: -the rotor provides...

With a larger diameter:
-the rotor provides more torque and stronger braking
-increases natural drag braking - less air gap
-improves the motorís initial throttle response (Acceleration) due to...
Forum: Slipperential discussion 10.01.2009, 10:07 PM
Replies: 5
Views: 4,505
Posted By prhess
You may also look at the springs, make sure they...

You may also look at the springs, make sure they are overlapped properly. I did not read the instructions (looked at the pictures only) and had the two springs overlapped incorrectly and it caused a...
Forum: Team Tekin 07.13.2009, 10:38 PM
Replies: 4
Views: 3,480
Posted By prhess
Hello, I ran both the 2200kv and 2650kv...

Hello,

I ran both the 2200kv and 2650kv castles-neus with my RX8, very smooth. I also ran the Tekin T8 2000kv truggy motor with my MMM, also very smooth. The tekin motor also allows the drive...
Forum: Team Tekin 07.05.2009, 03:24 PM
Replies: 215
Views: 54,005
Posted By prhess
Hello Yes the new rotors are shipping in...

Hello
Yes the new rotors are shipping in motors. I have put mine through 25 4s packs (15-16 RUNTIME) WITH NO ISSUES.

Great job Tekin.
Forum: Team Tekin 07.03.2009, 05:10 PM
Replies: 0
Views: 2,621
Posted By prhess
T8 Motor info and specs

Some good Motor info from another forum

T8 (Buggy) motors
TT2350 4030 2650kv - Delta - 2D
TT2351 4030 2050kv - Delta - 2.5D
TT2352 4030 1900kv - Wye - 1.5Y
TT2353 4030 1700kv - Delta - 3D...
Forum: General Electric 06.24.2009, 02:59 PM
Replies: 2
Views: 1,871
Posted By prhess
THANKS FOR THE HELP:yipi::party::mdr:

THANKS FOR THE HELP:yipi::party::mdr:
Forum: General Electric 06.24.2009, 01:25 PM
Replies: 2
Views: 1,871
Posted By prhess
Brian G, Wiring diagram help.

Hello Brian,

I was wondering if you can help me with a wiring diagram. I want to use a multimeter to measure my amp draw on my power supply. I am using an integy power strip...
Forum: Castle Creations 06.08.2009, 06:30 PM
Replies: 3
Views: 1,656
Posted By prhess
Then can't we provide a recomendation for lipos...

Then can't we provide a recomendation for lipos based on vehicle class with regard to lipo mah and C rating and cell count.

I would still like to get more information on the ESC and motor that is...
Forum: Castle Creations 06.08.2009, 05:56 PM
Replies: 3
Views: 1,656
Posted By prhess
MMM V3 Official Specs

Hello All,

I was thinking (very dangerous, do not want to let the magic smoke out of my head) could we get all the official specs on the Monster version 3 like:

Fan comes on at : 150 F
ESC...
Forum: Castle Creations 05.28.2009, 06:10 PM
Replies: 25
Views: 4,215
Posted By prhess
There were the best I could find ...

There were the best I could find

http://www.bocabearings.com/main1.aspx?p=product&id=16243&n=625-PP/TP/C3_Z/S_#5_AF2 - 99.99 a piece
or...
Forum: Castle Creations 05.28.2009, 05:55 PM
Replies: 25
Views: 4,215
Posted By prhess
Yes they are ABEC 1.

Yes they are ABEC 1.
Forum: Castle Creations 05.28.2009, 05:15 PM
Replies: 25
Views: 4,215
Posted By prhess
5x16x5 5mm - inside diameter 16mm -...

5x16x5

5mm - inside diameter
16mm - outside diameter
5mm - thickness

I know this for sure as I have replaced my castle-neus bearings. The front and rear are the same size.
Forum: Castle Creations 05.28.2009, 04:29 PM
Replies: 25
Views: 4,215
Posted By prhess
The tork 2200kv is the same motor as the neu...

The tork 2200kv is the same motor as the neu castle 2200kv, but is black instead of green
Forum: Castle Creations 05.28.2009, 04:07 PM
Replies: 25
Views: 4,215
Posted By prhess
I am assuming that they run they 5x16x5 bearing...

I am assuming that they run they 5x16x5 bearing as well.
Forum: Castle Creations 05.28.2009, 03:30 PM
Replies: 25
Views: 4,215
Posted By prhess
Hello, I swapped out all the bearings in my...

Hello,

I swapped out all the bearings in my 2650 and 2200 for ceramics from Boca. The rear cover does come off, but when I did the epoxy pulled off some electrical tape that is wrapped around the...
Forum: Buggy 05.01.2009, 02:47 PM
Replies: 6
Views: 2,270
Posted By prhess
Thanks

Hello to RC-monster community,

I would like to thank all of the members who contribute to this forum, I have built a great buggy all based on your experience. I have added a few mods of my own,...
Forum: Buggy 04.26.2009, 01:35 PM
Replies: 6
Views: 2,270
Posted By prhess
Here is a link to my jammin. The website is...

Here is a link to my jammin.

The website is far from complete, but I have plans to get it finished.

http://www3.telus.net/public/rhess2/x1cr.htm
Forum: Buggy 04.24.2009, 04:22 PM
Replies: 6
Views: 2,270
Posted By prhess
Nice Buggy!! I have done the same conversion. ...

Nice Buggy!! I have done the same conversion.

I also picked up a used roller on ebay. The diff gears were well worn, so I changed then out for hot bodies spiral diffs with hardened internals,...
Forum: Brushless 04.23.2009, 05:59 PM
Replies: 78
Views: 25,697
Posted By prhess
I have been using these on a tamiya F201 car and...

I have been using these on a tamiya F201 car and my 4-tec. They work well, the great thing is they use 12mm hexes

fronts 30mm foams
rears 40mm foams.



made by Kawahara - great name in...
Showing results 1 to 19 of 19

 
Forum Jump


RC Monster




Powered by vBulletin® Version 3.8.1
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.
vBulletin Skin developed by: vBStyles.com