RC-Monster Forums  
RC Monster

Go Back   RC-Monster Forums > Search Forums
Reload this Page Search Results

Page 1 of 15 1 2311 Last »
Showing results 1 to 25 of 372
Search took 0.01 seconds. Search: Posts Made By: Big House
Forum: Castle Creations 07.18.2016, 10:03 PM
Replies: 2
Views: 6,488
Posted By Big House
Fan comes on almost immediately

I have a question. I have a MMM V1 and I don't know why my the ESC fan comes on after one run. Temps with IR temp gun rarely exceeds 125 but fan constantly runs? Is this a glitch or something off...
Forum: Castle Creations 07.01.2016, 02:58 PM
Replies: 22
Views: 15,524
Posted By Big House
Please give us back the power in the XLX

For the Love of All that is fast and good when oh when is the new firmware coming out for the XLX. I hate being in the middle of a run and hear the power cut. Please give us back the power.
Forum: Castle Creations 06.22.2016, 09:04 AM
Replies: 1
Views: 4,493
Posted By Big House
Castle link works....but doesn't power up

My XL2 went out it seemed due to a cap pack coming disconnected from the ESC. I replaced the cap but the unit does not when I connect the battery. Anyone have any ideas?
Forum: Brushless 04.15.2016, 09:37 PM
Replies: 14
Views: 9,398
Posted By Big House
Anytime friend....you see the car in my...

Anytime friend....you see the car in my avaitar....it will get your Rusty....Fair winds and safe seas my friend.
Forum: Castle Creations 09.01.2015, 12:30 PM
Replies: 2
Views: 3,748
Posted By Big House
Can it be saved

My green can 1717 started making all kinds of god aweful sounds so I opened it up and found this. My question is can it be saved?
Forum: Castle Creations 08.13.2015, 09:58 PM
Replies: 4
Views: 4,553
Posted By Big House
Ripple voltage - safe zone

What is the safe zone for ripple voltage. I was comparing graphs of my XL2 with and with out cap packs and in looking at all three the highest ripple voltage i saw was 4v at 306 amps. Trying not to...
Forum: Castle Creations 08.12.2015, 06:38 PM
Replies: 2
Views: 3,845
Posted By Big House
Thanks. May have to make the switch permanent. ...

Thanks. May have to make the switch permanent. The sled weighs in about 5lbs under the limit and the motor is 2150kv I think.
Forum: Castle Creations 08.11.2015, 10:45 PM
Replies: 2
Views: 3,845
Posted By Big House
Mamba Monster vs XL2

Question...I have an V2 Mamba Monster and an XL2. With the same motor, the Monster Mamba out performs the XL2 at low speed with little to no clogging. Why is this and besides the 8s capability, is...
Forum: Brushless 08.06.2015, 10:52 PM
Replies: 14
Views: 9,398
Posted By Big House
The Beast -Back and better than ever...

After about a month and a half of cutting, trimming, painting, testing and glassing, the monster is back and better than ever. Changed the gearing to go faster and the color to see better at longer...
Forum: Brushless 06.20.2015, 04:17 PM
Replies: 14
Views: 9,398
Posted By Big House
The casualties of the crash and the new stuff

I thought it would have been worst. Only broke a few things and the best part, the front and rear shocks have already be re-built, better than ever. 4mm carbon fiber, this is not breaking.
Forum: Brushless 06.19.2015, 04:05 PM
Replies: 14
Views: 9,398
Posted By Big House
The damage assessment ...

I finally got a chance to tear down the wreckage and it wasn’t nearly as bad as it looked. *The chassis is completely intact. *The 4.4mm CF chassis Held up beautifully against the curb and was wholly...
Forum: Brushless 06.15.2015, 04:24 PM
Replies: 14
Views: 9,398
Posted By Big House
Absolutely...I think things would have been worse...

Absolutely...I think things would have been worse had the top not been on. Even more, the shell is fiber glassed.
Forum: Brushless 06.15.2015, 12:38 PM
Replies: 14
Views: 9,398
Posted By Big House
Serum....I like the speed...and that was my...

Serum....I like the speed...and that was my goal...100 plus on 6s. And I thought it was worse as well until I saw it up close. The carbon fiber didn't break at all...the plastic and aluminum parts...
Forum: Brushless 06.14.2015, 11:03 PM
Replies: 14
Views: 9,398
Posted By Big House
Gentlemen we can rebuild him...we have the technology

Yeah I stole that from the Six million dollar man because that is how I feel. On what began as a beautiful run up to 102mph, I didn't get out of it soon enough and he caught a curb, caught air and...
Forum: Castle Creations 05.22.2015, 11:11 PM
Replies: 18
Views: 27,300
Posted By Big House
Start up clogging

Like the title says, I get really bad initial clogging. No matter how easy I get into the throttle, start up clogging horrible. Once I get it going, the issue goes away, but getting to that point...
Forum: Brushless 05.17.2015, 09:12 PM
Replies: 0
Views: 3,856
Posted By Big House
DM-1 speed car project

I had a spare DM-1 Pro roller chassis laying around and decided to cut it down to a 360mm wheel base for a new speed run car. The DM-1 Pro had a wheel base of roughly 379mm so I cut 19mm out of the...
Forum: General Questions 02.19.2015, 09:47 PM
Replies: 9
Views: 13,185
Posted By Big House
Figured out the issue. Tested another unit in my...

Figured out the issue. Tested another unit in my GTP and plugged in the gain wire and boom...working like a dream in both my GTP and my LST2.
Forum: General Questions 02.19.2015, 11:51 AM
Replies: 9
Views: 13,185
Posted By Big House
I am using the HK-401b...

I am using the HK-401b...
Forum: General Questions 02.17.2015, 03:08 PM
Replies: 9
Views: 13,185
Posted By Big House
Ok...thanks. another question. Does it matter...

Ok...thanks. another question. Does it matter where the gryo unit is placed. I ask this because when testing to see if the wheels stay in place, they don't really move as I.have.seenin a number of...
Forum: General Questions 02.17.2015, 12:32 PM
Replies: 9
Views: 13,185
Posted By Big House
Gyro with dual servo trucks

I have a question. I am trying to install a gyro in my LST2 with dual servo steering. My question is this: do I need two gyros, one for each servo or should the one gyro handle both?
Forum: Brushless 01.27.2015, 11:51 PM
Replies: 0
Views: 4,246
Posted By Big House
The newest Stallion in the stable

After a few months of measuring, cutting, drilling, sanding and assembly, the newest stallion takes it place int he corral. Serpent 966 joined a Power Racing XR80 to form a beast of epic...
Forum: Brushless 12.13.2014, 11:13 PM
Replies: 11
Views: 5,696
Posted By Big House
In one of my models, I never had an issue...

In one of my models, I never had an issue mounting the reciever atop the servo.
Forum: Brushless 12.06.2014, 04:00 PM
Replies: 11
Views: 5,696
Posted By Big House
Brushless Losi, Yeah, I got my Losi back on...

Brushless Losi,

Yeah, I got my Losi back on the road. Hitting a tree and plastic does not mix. I reassembled the rear end and all was well. I dropped the stance using some leftover carbon...
Forum: Brushless 11.30.2014, 11:30 PM
Replies: 5
Views: 5,142
Posted By Big House
1717 and a XL2 is the perfect combo. Running...

1717 and a XL2 is the perfect combo. Running this in my LST2.
Forum: Brushless 11.30.2014, 11:20 PM
Replies: 11
Views: 5,696
Posted By Big House
I have a custom set-up where I am running a 26/51...

I have a custom set-up where I am running a 26/51 combo...fast as stink and torque happy. Running a Big Block Mamba from a XO-1. Check out the following thread.
...
Showing results 1 to 25 of 372
Page 1 of 15 1 2311 Last »

 
Forum Jump


RC Monster




Powered by vBulletin® Version 3.8.1
Copyright ©2000 - 2021, Jelsoft Enterprises Ltd.
vBulletin Skin developed by: vBStyles.com

Contact Us - RC-Monster Store - Archive - Top